Anybody know where I can get some 3/32" shafted .050" tire tool replacement tips? They fit the old style Camen and Pro Slot tire tools.
.050" tire tool replacement tips
Started by
brnursebmt
, Nov 29 2016 03:57 PM
8 replies to this topic
#1
brnursebmt
-
- Full Member
-
- 846 posts Joined: 17-February 06
Race Leader
- Gender:Male
- Location:Glencoe, AL
Posted 29 November 2016 - 03:57 PM
Bobby Robinson RN, BMTCN
"Nobody rides for free." - Jackson Browne, 1980
"Positivity and optimism can overcome a lot of things." - Tom Brady, 2019
"Trying is the first step towards failure." - Homer Simpson
#2
John Streisguth
-
- Full Member
-
- 5,638 posts Joined: 20-November 08
Johnny VW
- Gender:Male
- Location:Bangor, PA
Posted 29 November 2016 - 04:19 PM
Not sure about those, but I just ordered a half dozen for the Parma tools. Should be here "any day now." LOL.
"Whatever..."
#3
PCH Parts Express
-
- Full Member
-
- 2,496 posts Joined: 27-December 09
Posting Leader
- Gender:Male
Posted 29 November 2016 - 04:21 PM
The Koford M162 will work in most wrenches with set screw retainers. The diameter of the M162 may be smaller than you want. JK makes two tips of different diameters. What is the shaft diameter you need?
Scott Salzberg
PCH Parts Express
#4
Eddie Fleming
-
- Subscriber
-
- 2,909 posts Joined: 27-April 14
Posting Leader
- Gender:Male
- Location:Fayetteville, GA USA
Posted 29 November 2016 - 04:31 PM
I have looked for those too Bobby. The JKs I tried did not fit. If you find one it will need to be long enough or small enough on the end to go down in the hole of a big full hub, but you probably new that. Let me know if you find any.
that shaft size is .093 I think.
Eddie Fleming
#5
Tim Neja
-
- Subscriber
-
- 6,839 posts Joined: 11-June 07
Grand Champion Poster
- Gender:Male
- Location:Paso Robles
Posted 29 November 2016 - 04:39 PM
The Koford M162 will work in most wrenches with set screw retainers. The diameter of the M162 may be smaller than you want. JK makes two tips of different diameters. What is the shaft diameter you need?
He said 3/32 Scott--FYI
She's real fine, my 409!!!
#6
brnursebmt
-
- Full Member
-
- 846 posts Joined: 17-February 06
Race Leader
- Gender:Male
- Location:Glencoe, AL
Posted 29 November 2016 - 04:56 PM
The shaft size is .093......3/32.
The old Parma tools were 3/32 too. Wonder if the new ones are the same?
Bobby Robinson RN, BMTCN
"Nobody rides for free." - Jackson Browne, 1980
"Positivity and optimism can overcome a lot of things." - Tom Brady, 2019
"Trying is the first step towards failure." - Homer Simpson
#7
S.O. Watt
-
- Full Member
-
- 1,181 posts Joined: 24-June 06
Graduate Bench Racer
- Gender:Male
- Location:Glen Cove, Key Penisula, Wa.
Posted 29 November 2016 - 05:09 PM
All my old Camen wrench handles are now bored out to take a 3mm x .050 replacement tip from Hudy.
- Rob Voska and boxerdog like this
Tom Hansen
Our Gang Racing Team
Cukras Enterprises
Team Camen
Chassis By Hansen
I race and shop at Pacific Slot Car Raceway
#8
PCH Parts Express
-
- Full Member
-
- 2,496 posts Joined: 27-December 09
Posting Leader
- Gender:Male
Posted 29 November 2016 - 05:38 PM
If you don't mind the tip working perfectly but only being 2mm get the Koford tip.
Scott Salzberg
PCH Parts Express
#9
bluecars
-
- Member at Peace
-
- 1,273 posts Joined: 26-June 13
Checkered Flag in Hand
- Gender:Male
- Location:Tuskegee, AL
Posted 29 November 2016 - 07:35 PM
Shirley has some short ones.
Robert 'Red' Valantine
9/18/51-8/30/24
Requiescat in Pace
9/18/51-8/30/24
Requiescat in Pace
