Jump to content




Photo

Womp-A-Palooza - Jun 14, Houston, TX


  • Please log in to reply
3 replies to this topic

#1 CARSHouston

CARSHouston

    Backmarker

  • Full Member
  • PipPip
  • 97 posts
  • Joined: 19-November 11
  • Gender:Male
  • Location:Houston

Posted 13 May 2020 - 08:30 PM

Womp-A-Palooza coming to Slot Car Raceway in Houston on June 14, 2020.

 

Details tomorrow.


George Marsanick Jr




#2 CARSHouston

CARSHouston

    Backmarker

  • Full Member
  • PipPip
  • 97 posts
  • Joined: 19-November 11
  • Gender:Male
  • Location:Houston

Posted 14 May 2020 - 09:09 AM

We will be running 3 races/classes, but only one set of chassis rules.
For the Legends class we will use the below AWRA Outlaw Legends rules with the following Slot Car Raceway changes.
Only 1/8" axles front and rear
.062 clearance
No cut down guides
Interior is required in Legends and GT1 and can have wing car style driver in Sportsman.

 

The Sportsman and GT1 classes will only need to change the body, you can use the same chassis/chassis rules for all 3 races.
GT1 first race on the Hill Climb
Sportsman second race on the King
Legends last race on the Hill Climb

 

***Outlaw Legends Class***
Chassis:
Parma Womp Steel #572
Parma Womp Brass #573
K&G Brute #16-02
Champion Thumper #400
Champion Thumper #401
LVJ Charger Brass #LVJ002B
LVJ Charger #002
Riggen #5003
Mid America Stomp #MAR 202
R-GEO Raven #RGO-335
H&R Stinger #HRST01
Bracing is permitted. Motor mount may be cut off. Motor must be mounted 90 degrees to the rear axle. Drilling,
grinding, bending, cutting of the chassis is permitted. Chassis must remain as a “one piece” unit. No “flexi”
style multi-piece modifications are permitted. Additional weight is permitted. LVJ Chassis must have the front
screws assembled with Lock-Tite (or equivalent) and be tight to the chassis. Offset axle bushings are permitted.
No ball bearings
LVJ Chassis must have the front screw assembled with Lock-Tite (or equivalent) and be tight to the chassis.

 

Width & Wheel Base:
Width: 3 1/4” centered with no offset or excessive slop. Width is to be measured by any commercially
available manufacturer’s tech tool. (ie. Koford, Parma, Champion, etc.)
Wheel Base: Maximum of 3 1/8” center to center of the axles.

 

Clearance:
.062 clearance measured form under the motors end bell back including the crown gear.

 

Motor:
Parma 16D #501
Parma 16D Home Set #458
JK Hawk25 #JK303025
Pro Slot 16D #4000
Pro Slot 16D #4001
H&R Stingray #HRMS1
JK Mini Brute #JKHMB
Hawk 7 #30307
H&R Cobra 3 HRMC1
JK Retro Hawk #JKHR
Kelly Bullet #KE532
H&R Lightning #HRML1
H&R Crusher #HRMx1
Professor Motor Retro # PMTRHR
No American armatures or neo magnets. Single ceramic magnet only. Magnets may not be shimmed or glued.
Motor must be mounted in line at 90 degrees to the rear axle. JK Motors must be mounted with motor ID stamp
visible. Motor may be tack soldered in place.
This list of motors is not compiled to mean all are equally competitive. Some motors are included to allow
novice or young racers to be included without becoming an obstacle to experienced racers. We trust parents to
consider this when selecting for young children and help provide a fun day of racing for all.

 

Guide Flag:
No cut down guides, otherwise any flag that is commercially available. No shortening of the guide flag. Cutting excess above the nut is
permitted.

 

Tires & Axles:
Front: 1/8” axle and 3/4” diameter front tire. Hollow axles are allowed. Independent front axle
combinations are allowed. O-ring fronts are accepted. No rounding, curving, coning or painting of foam rubber
tires.
Rear: 1/8” solid or hollow axle with any brand or diameter tire providing the required minimum
clearance.

 

Gears:
48 pitch only. Beveled gears are permitted.

 

Body:
Any commercially available legends style full fender coupe, sedan or coach (1940 style or earlier) WOMP
body. Bodies with added roof spoilers are not legal regardless of whether the body was manufactured in that
configuration. Running boards cannot be modified from the stock configuration to facilitate lowering of the
body. Fenders may not be trimmed to excess. Body must be painted a minimum of 1 color and have numbers
displayed on three sides of the body. (ie. roof, doors, trunk, hood) Interior is required in Legends and GT1 and can have wing car style driver in Sportsman.


George Marsanick Jr

#3 CARSHouston

CARSHouston

    Backmarker

  • Full Member
  • PipPip
  • 97 posts
  • Joined: 19-November 11
  • Gender:Male
  • Location:Houston

Posted 14 May 2020 - 05:20 PM

Any Legends, GT1 or Sportsman body listed in the AWRA rules will be legal with the exception of the Late Model Wedge, it's not legal to use.
For local racers, P.A. has some Ford legends and Corvette GT1 bodies in stock.
For any body that P.A. doesn't have your best choice is to order them from here

 

http://www.cavemanbodeez.com/

 

Just click on Products, click on 1/32 bodies and finally click on AWRA legal bodies and make your choices.


George Marsanick Jr

#4 CARSHouston

CARSHouston

    Backmarker

  • Full Member
  • PipPip
  • 97 posts
  • Joined: 19-November 11
  • Gender:Male
  • Location:Houston

Posted 18 May 2020 - 01:58 PM

Schedule
Raceway opens 9 AM
GT1 Tech 11 - 11:30 AM
GT1 race 12 noon on the Hill Climb
Followed by Sportsman on the King and Legends back on the Hill Climb


George Marsanick Jr





Electric Dreams Online Shop