Events for February 18, 2011

On Saturdays, the racing at J & B Raceways alternates between Indy & 4-1/2" NASCAR one week, with Hot Rod and 4-1/2" Truck the next week.

Racing for first class (Indy or Hot Rod) starts at 2 PM.

Racing for the second class (4-1/2" NASCAR or 4-1/2" Truck) starts at 4 PM.

$7 entry fee.

J & B Raceways
2215 N. Fifth St
Fremont, OH 43420
(419) 334-2100
http://www.jandbraceway.com

Come join us for our Appliance GuyZ sponsored GTP Parma 502 race series on Saturday nights.

More information can be found at HERE.

Slot Car Cave
3033 Cherry Road, Suite B
Rock Hill, SC 29730
(803) 524-8844

Tom Thumb Hobbies, Columbus, OH.

Can-Am, F1, Retro Flexi, RetroPro classes.

For more details see THIS POST in the ORS Forum under IRRA Racing.

TRRA D3 Retro Can-Am and Flexi GTR (Viper, Corvette, Saleen, etc.) at Ranger Raceway.

130' Ogilvie flat track.

Ranger Raceway
2014 Silver Street
Garland, TX 75042
(NW of Dallas)
(214) 243-0468

Central TN Raceway
208 Old Nashville Hwy
Lavergne, TN 37086
(615) 556-9167

Saturday, February 19

Times are approximate. Be here earlier than listed start times!!

8 AM - Raceway opens for practice

10 AM - 4½” FCR Retro Stock Car

Motors: Sealed Parma 16D motors, may change brushes and springs only.
Body: IRRA™ approved bodies ONLY. They must measure 1-7/8” on the roof of the car. Body must be painted with three (3) numbers on the body (roof and both doors). MUST have a Champion #361C interior taped in the front and rear. NO drooping allowed. MUST NOT be able to see any of the chassis when you look at the car from above the car.[/b]
Tires: Any black tire, front & rear. Super glue & CLEAR finger nail polish allowed on front tires. Independent rotating front tires are allowed. Min. front tire .810" diameter .400" wide.
Chassis: Bushings MUST be in the UP position front and rear. Bushings or chassis CAN NOT be altered in anyway to change position of axle. Minimal bracing to the uprights is allowed (uprights and motor box). Bracing from rear of the chassis to the front is NOT allowed. Rear chassis and gear clearance is .050".
Lead Wire & Guide: Any wire and guide can be used.

$10 entry fee with $3 divided to the top three spots.

12 PM - FCR 4½” Trucks

Rules same as Retro Stock Car except for body.
Body: Must be minimum 1-7/8” on the roof setting on tech block. NO Kelly truck bodies allowed. Front bumper ¼”and rear bumper 1/8” must be left on the body.

$10 entry fee with $3 divided to the top three spots.

2 PM - GTP

Chassis: Any 4” chassis allowed. No drilling of chassis to make the chassis lighter. You can drill the motor box for better gear mesh but the original motor box must remain. You can add weight to the chassis, top or bottom.Chassis and gear must pass the .063" clearance.
Body: Any GTP body allowed. No numbers required but you may want to have some just in case there are two or more cars with the same color. Some kind of driver required.
Motor: S16D arm in a D-can. You can build your motor (ex. truing the arm, any brushes, springs etc). NO bearings in the can. NO C-cans. NO tagged arms.

$10 entry fee with $3 divided to the top three spots.

3 PM - Box 12 Wing Car

$12 entry fee with $5 divided to the top three spots.

MASON DIXON RETRO

Saturday, Feb. 19, 2011

Race #7 of the 2010-11 Season

DT Hobbies
1100 Carlisle Street
Hanover, PA 17331
(717) 646-8381

Practice starts at 8 AM.

GT Coupe Amateur starts at 10 AM.
F1
Can-Am

IRRA™ rules to be used in all classes.