Jump to content




Photo

Arm winding #1

Closed due to length

  • This topic is locked This topic is locked
3573 replies to this topic

#2526 Kim Lander

Kim Lander

    Race Leader

  • Full Member
  • PipPipPipPipPip
  • 631 posts
  • Joined: 06-June 09
  • Gender:Male
  • Location:Macon, GA

Posted 09 February 2011 - 03:34 PM

Hey John,
As you well know, balanced mags are the real key in a balanced motor, if mags arent the same strength they tend to fight each other when the juice is poured on, especially if they are STRONG mags, BUT, if you use some like in the new strap-nut on steroids, you have to have a wind strong enough to have the KAHONA`S to turn , if not you are right back to what Victor said about his 16-d with the weaker mags , it just didnt have the back-bone to turn the way it should. As usual...you put things like this motor in front of me just to tease me...kind of like dope in front of a crack-head. O need to go play with my motors now...seeya later. Keep up the BEAUTIFUL work.Oh by the way....GOT SNOW ....couldnt resist.LOL
Kim




#2527 havlicek

havlicek

    OCD Rewinder

  • Subscriber
  • PipPipPipPipPipPipPipPip
  • 11,198 posts
  • Joined: 20-August 07
  • Gender:Male
  • Location:NY

Posted 09 February 2011 - 03:48 PM

Hi Kim,

For sure, and these magnets were really matched...maybe I just got a lucky pair??? Anyway, the motor has settled down a little now and draws around 5 amps...still running at 5.5V. Of course, this thing will need to not get very hot to avoid killing these magnets...but I think (?) that even the #26 wind is not quite strong enough and that maybe the #25 will do the trick here. This goes against everything I'd expect, but if the #25 doesn't seem right, I may do a #27 and see how that goes...a little shade tree R&D going on here :rolleyes::laugh2: I think I'm going to try one of Bill Bugenis' arms/coms for the next one and have him do his balancing magic on it. This is strong medicine and needs all the insurance it can get. Maybe I'll wind both arms at the same time and have them both ready to install and see what's what. Like I said, I'm flying blind here...but I haven't slammed into anything yet.:unsure:

-john
John Havlicek

#2528 Victor Poulin

Victor Poulin

    Posting Leader

  • Full Member
  • PipPipPipPipPipPipPip
  • 2,097 posts
  • Joined: 04-March 08
  • Gender:Male
  • Location:Raymond, NH

Posted 09 February 2011 - 04:44 PM

John,
I,ve got some of the mags on their way and as soon as I can, I'll take a gauss reading on them just to see what kind of match we get. I hope my results are as good as yours lol, I,ll be very happy. I just want to see if yours were a fluke, or if their all matched.

Vic
Alright, who cut the cheese?

#2529 MantaRay

MantaRay

    a dearly-missed departed member

  • Member at Peace
  • PipPipPipPipPipPipPip
  • 2,859 posts
  • Joined: 05-March 06
  • Gender:Male
  • Location:Chicagoland

Posted 09 February 2011 - 04:55 PM

John, What did you glue the magnets in with...........what is the air gap?
tx
Ray
Ray Price
11/4/49-1/23/15
Requiescat in Pace

#2530 Alchemist

Alchemist

    Posting Leader

  • Full Member
  • PipPipPipPipPipPipPip
  • 2,840 posts
  • Joined: 11-November 09
  • Gender:Male
  • Location:Far, far away

Posted 09 February 2011 - 05:12 PM

As usual...you put things like this motor in front of me just to tease me...kind of like dope in front of a crack-head.


LOL John!!

I'm in the same boat as Kim except I see it like "Chocolate". I'll admit I'm a "Chocoholic"!!!! hahaha!

Ernie
Ernie Layacan

#2531 havlicek

havlicek

    OCD Rewinder

  • Subscriber
  • PipPipPipPipPipPipPipPip
  • 11,198 posts
  • Joined: 20-August 07
  • Gender:Male
  • Location:NY

Posted 09 February 2011 - 05:17 PM

Hi Ray,

Both the shims and the magnets are glued-in with JB Weld...in fact, the magnets are so strong they kept pulling some of the JB Weld (it has steel powder in it) off the toothpick. The airgap measures at around .518" with the F7 can and a set of F7 can sides cut to use as shims. I dulled the back of the magnets with a light touch of Scotchbrite and then cleaned them with acetone before epoxying them since the nickle plating on these is very slippery. I wanted to make sure there was a good bond.

-john
John Havlicek

#2532 MantaRay

MantaRay

    a dearly-missed departed member

  • Member at Peace
  • PipPipPipPipPipPipPip
  • 2,859 posts
  • Joined: 05-March 06
  • Gender:Male
  • Location:Chicagoland

Posted 09 February 2011 - 05:25 PM

Thanks John, I ordered a couple pair.........I will take look and measure and decide to shim or not to shim........What do you use to cut/shorten and trim the cans? Just a Dremel?
Ray Price
11/4/49-1/23/15
Requiescat in Pace

#2533 Victor Poulin

Victor Poulin

    Posting Leader

  • Full Member
  • PipPipPipPipPipPipPip
  • 2,097 posts
  • Joined: 04-March 08
  • Gender:Male
  • Location:Raymond, NH

Posted 09 February 2011 - 05:29 PM

LOL John!!

I'm in the same boat as Kim except I see it like "Chocolate". I'll admit I'm a "Chocoholic"!!!! hahaha!

Ernie



I'm telling ya Ernie, you really got to give this stuff a try. Its a real hoot !! Even if you cant do your own arms you can still stuff different arms into these things untill you find the magic one lol. That's what I do for now untill I learn to wind my own. I love it !! I'm like a crack addict, I can't get enough :laugh2:
If you start with some old used up falcons or simular motors, the worst that can happen is that you wind up having to toss one and start over untill you get it right.
No big deal !

Vic
Alright, who cut the cheese?

#2534 havlicek

havlicek

    OCD Rewinder

  • Subscriber
  • PipPipPipPipPipPipPipPip
  • 11,198 posts
  • Joined: 20-August 07
  • Gender:Male
  • Location:NY

Posted 09 February 2011 - 06:29 PM

You've that 60's spirit for sure Vic :) The only thing missing is the acrid smell of melting Mabuchi end bells!

Thanks John, I ordered a couple pair.........I will take look and measure and decide to shim or not to shim........What do you use to cut/shorten and trim the cans? Just a Dremel?


Always glad to help Ray. I just use the Dremel thin cutoff discs, they slice through the can material without much difficulty. You can't force them though since they crumble from just looking at them wrong :) I've settled on using a piece of 3/4" brass to scribe the outside of the can before cutting. Using a 3/4" (.750") outside length, I can get as much as a .330" long stack in there with a full size com...but I use a .300" stack most often as it's a comfortable fit. I think an X-12 arm will fit in this with just some trimming of the tail spacer. The cans are strong and stiff enough to hold up well to a lot of hacking...they're also straight and true.

-john
John Havlicek

#2535 Alchemist

Alchemist

    Posting Leader

  • Full Member
  • PipPipPipPipPipPipPip
  • 2,840 posts
  • Joined: 11-November 09
  • Gender:Male
  • Location:Far, far away

Posted 09 February 2011 - 10:34 PM

I'm telling ya Ernie, you really got to give this stuff a try. Its a real hoot !


That's my plan Vic - eventually!!!

Thanks!

Ernie
Ernie Layacan

#2536 Prof. Fate

Prof. Fate

    a dearly-missed departed member

  • Member at Peace
  • PipPipPipPipPipPipPipPip
  • 6,580 posts
  • Joined: 20-February 06
  • Gender:Male
  • Location:Salt Lake City, UT

Posted 10 February 2011 - 12:41 PM

Hi

I wish I knew a basic forumla about when "too much" happens.....grin. I have run monster mags on very mild winds, and then gone to a taller gear to get them "singing".

I once built a "stock" cheater 16d on a dare from the track owner for a womp with cobalts inside the ceramic magnets and a blue wire stock 30 s wind. My car was about an ounce heavier than the other womps, which could not pull more than 3.5 without heating up. I was running 2.2, out accelerating everyone, out breaking and out running. This was a special for a old stock blue king and I don't remember if I ever tried it on a smaller track.

Fate
Rocky Russo
3/6/48-1/1/12
Requiescat in Pace

#2537 MantaRay

MantaRay

    a dearly-missed departed member

  • Member at Peace
  • PipPipPipPipPipPipPip
  • 2,859 posts
  • Joined: 05-March 06
  • Gender:Male
  • Location:Chicagoland

Posted 10 February 2011 - 01:21 PM

John, Thanks for the cutting tips..........
Ray Price
11/4/49-1/23/15
Requiescat in Pace

#2538 havlicek

havlicek

    OCD Rewinder

  • Subscriber
  • PipPipPipPipPipPipPipPip
  • 11,198 posts
  • Joined: 20-August 07
  • Gender:Male
  • Location:NY

Posted 10 February 2011 - 07:22 PM

You're most welcome Ray. Let me know how you make out and/or if I can offer any more tips :) BTW...have I ever mentioned that the Manta Ray is the coolest thingie ever (ducking)? :)

-john
John Havlicek

#2539 havlicek

havlicek

    OCD Rewinder

  • Subscriber
  • PipPipPipPipPipPipPipPip
  • 11,198 posts
  • Joined: 20-August 07
  • Gender:Male
  • Location:NY

Posted 11 February 2011 - 12:27 PM

OK, so I did some more experimenting on the Strapnut setup with the Emovendo neos shimmed pretty tight (.519-ish airgap). First try with a #26 ran very well, drew a healthy amount of current and had seemingly loads of torque and with almost no run-down (it stopped dead when power was taken off). I did a #28 wind yesterday and that ran just OK, current draw was still up there and it seemed pretty clear that the arm just wasn't up to the magnets. So it seemed obvious that I was going to have to go "the other way" and try something hotter than the first #26. I had one of Mura's current .007" lam arms lying around here, so I shortened the stack to .330" and installed one of Bill Bugenis' lovely coms. For the wind, I did a #25 that's very close to what I've done recently for Bill and Lou Pirro figuring that had to be at least "ballpark". The arm balanced up nicely, so I popped it in the setup to see what's what...here's what I got:

Posted Image

This thing is pretty danged impressive. After pretty much no break-in, it screams at 5.5V and draws just about 5 amps no load. Spinup and spin down are almost instant and it really doesn't get all that warm surprisingly. In the right car, I could see this being a blistering motor for some casual laps...but I really think this would be a great drag motor. I could see this same setup taking a #24...maybe even a #23 wind and doing reasonably well considering how ...er...unreasonable those winds are :) Of course, you could run these magnets with a wide airgap and a milder arm...but what would be the fun in that??? This thing has loads of revs and arm-twisting torque.

-john
John Havlicek

#2540 Victor Poulin

Victor Poulin

    Posting Leader

  • Full Member
  • PipPipPipPipPipPipPip
  • 2,097 posts
  • Joined: 04-March 08
  • Gender:Male
  • Location:Raymond, NH

Posted 11 February 2011 - 02:48 PM

Thats cool John!! It sounds to me like it would make one heck of a drag motor. Prob a good motor for lots of different things, but where high heat might be a factor, I'm thinking better for drag. I think if you were to list this motor for sale listed under drag motor, you may be very supprised at what it would fetch :rolleyes:

Vic
Alright, who cut the cheese?

#2541 havlicek

havlicek

    OCD Rewinder

  • Subscriber
  • PipPipPipPipPipPipPipPip
  • 11,198 posts
  • Joined: 20-August 07
  • Gender:Male
  • Location:NY

Posted 11 February 2011 - 04:48 PM

Hi Vic,

Yeah, it would make a great drag motor...even better because it's so small and light. It's also a very lo-tech version of a eurosport motor so, with the right doo-dads (shunts, better springs and brushes) and some choke...it probably would be cool in a road car. When you get up into this territory though, you can't really be sure it can be run hard. At least this one has a new com and Bill's coms have worked really well under stress.

On the sale thing, at least something like this has several possibilities for actually running. Stuff like old Muras and Mabuchis can really only be casual goofing around (except for the occasional thingie fest).

-john.
John Havlicek

#2542 Alchemist

Alchemist

    Posting Leader

  • Full Member
  • PipPipPipPipPipPipPip
  • 2,840 posts
  • Joined: 11-November 09
  • Gender:Male
  • Location:Far, far away

Posted 11 February 2011 - 11:25 PM

Hi John,

I'll take 2 please!! LOL!! Why do you always temp me with your goodies John - it's like chocolate. . . . ..... and you know I'm a chocoholic - hahahahaaa!

I really wish we could hear them "scream" under power! KOOL John - thank you for sharing.

Ernie
Ernie Layacan

#2543 havlicek

havlicek

    OCD Rewinder

  • Subscriber
  • PipPipPipPipPipPipPipPip
  • 11,198 posts
  • Joined: 20-August 07
  • Gender:Male
  • Location:NY

Posted 12 February 2011 - 08:46 AM

Hi Ernie, your enthusiasm is absolutely contagious...makes me want to build more motors! After I clear my table of projects, I'll be doing more Strapnuts for sure...but for now it's back to Mabuchi Land with a pile O' 26Ds and 36Ds waiting to git dun :) "Motors motors everywhere and not a drop to drink" (gotta make some more coffee!)...or is it..."don't wind until you see the whites of their endbells" ? :)

-john

PS...those new Hawk endbells look like they might be a nice shortcut for cranking out Strapnuts! Going to give those a try very soon so...stay tuned!
John Havlicek

#2544 havlicek

havlicek

    OCD Rewinder

  • Subscriber
  • PipPipPipPipPipPipPipPip
  • 11,198 posts
  • Joined: 20-August 07
  • Gender:Male
  • Location:NY

Posted 12 February 2011 - 12:52 PM

I've pretty well cleared my table of projects, having finished off some Proxy motors. That gave me the time to focus on a 36D for Dave Cummerow (aka "boxerdog"). Dave's a 36D fan and sent me a minty-fresh Champion can with the can shim and Arcos installed. He also sent an endbell that had been fitted with modern brush hoods..."something old/something new" :) Since he saved me the work, I figured I'd go the extra mile on his project and do something I don't think he has. For the arm, a long stack Tradeship and matching Tradeship 36D com (the one with the zero timing advance) made up the blank. I set the timing to a mild 10-ish degrees and did him a #30 double wind. This one is a double wind off two spools, rather than a "layered" or sequenced double. I think winding a double this way is maybe a better way to do it as you're pretty sure both coils on each pole are the same length. The arm came out really nicely measuring between .4 and .5 ohm and drawing only slightly above 1 amp (no load). As you would expect of a double, it runs strong but doesn't get too warm.

Posted Image


Double winds are more work and getting them neat is a pain, but I think they're especially cool for these old motors. The arm balanced out beautifully and it was time to move it into it's new home:

Posted Image

Like I said, a strong and smooth runner and the updated endbell hardware should provide a little extra insurance. Nice thing about the Tradeship blanks is that there's enough shaft to go either endbell drive or can drive!

-john


John Havlicek

#2545 boxerdog

boxerdog

    Race Leader

  • Full Member
  • PipPipPipPipPip
  • 877 posts
  • Joined: 10-November 10
  • Gender:Male
  • Location:Modesto, CA

Posted 12 February 2011 - 01:46 PM

John, not only is that thing a work of art, it is amazing that you crank out that stuff so quickly and precisely. I'll put it in one of my Riggens or American Lines and see what it says. Thanks for all of your efforts!!
dc
David Cummerow

#2546 havlicek

havlicek

    OCD Rewinder

  • Subscriber
  • PipPipPipPipPipPipPipPip
  • 11,198 posts
  • Joined: 20-August 07
  • Gender:Male
  • Location:NY

Posted 12 February 2011 - 01:56 PM

Thank YOU Dave.

it is amazing that you crank out that stuff so quickly and precisely


The "precise" thing I just try real hard at. The "quick" thing is an illusion :) ...especially when it comes to double winds like this one. Keeping both wires flat and straight (especially when "turning around" at the end of each layer) is a chore. It just so happens that I like this kind of chore :)...but it does take some time. Because I'm doing tiny "strapnut" motors with fat wire one day, and big honkin' FT36Ds with skinny wire the next, I almost always have to do some testing before winding to plan out the coils and patterns. If I was doing the same motors every day, THEN it would be quick!

Anyway, the pleasure was all mine Dave. Let me know what you think of the double wind. Typically, they run cooler than their equivalent single wind (in this case, a #27)...but sometimes may not have as much brakes, although that depends somewhat on the car and the gearing. It should be a really nice runner, doing about what a period rewind would do. Your package is going out in a little while, so it should be back to you by the middle of this coming week or so.

-john
John Havlicek

#2547 Victor Poulin

Victor Poulin

    Posting Leader

  • Full Member
  • PipPipPipPipPipPipPip
  • 2,097 posts
  • Joined: 04-March 08
  • Gender:Male
  • Location:Raymond, NH

Posted 12 February 2011 - 02:13 PM

PS...those new Hawk endbells look like they might be a nice shortcut for cranking out Strapnuts! Going to give those a try very soon so...stay tuned!



:laugh2: I was thinking the exact same thing John. I have a couple, but haven't had the chance to fiddle around with one yet.

Vic
Alright, who cut the cheese?

#2548 havlicek

havlicek

    OCD Rewinder

  • Subscriber
  • PipPipPipPipPipPipPipPip
  • 11,198 posts
  • Joined: 20-August 07
  • Gender:Male
  • Location:NY

Posted 12 February 2011 - 05:20 PM

Hi Vic,

Yes, having a quality endbell that fits the smaller can size without hacking er...finessing a C can endbell could be a real timesaver! I kind of like the way the larger C can endbell looks on there, sort of adds a little "wildness" to the look and a larger endbell should be a good thing for airflow/cooling. Still, I'm looking forward to trying one out. I forget whether the Hawk endbell used a "standard" 5mm or 6mm bushing hole...and don't know whether the new one does.
Posted Image

I seem to remember that, on the old one you had to shorten the brushes a little or they'd hit the spring arm??? I'll have to get some from Roger.

-john
John Havlicek

#2549 Bill from NH

Bill from NH

    Age scrubs away speed!

  • Full Member
  • PipPipPipPipPipPipPipPip
  • 15,393 posts
  • Joined: 02-August 07
  • Gender:Male
  • Location:New Boston, NH

Posted 12 February 2011 - 05:26 PM

John, I'd be real surprised if the Hawk endbell used a 6MM bushing. :)
Bill Fernald
 
I intend to live forever!  So far, so good.  :laugh2:  :laugh2: 

#2550 havlicek

havlicek

    OCD Rewinder

  • Subscriber
  • PipPipPipPipPipPipPipPip
  • 11,198 posts
  • Joined: 20-August 07
  • Gender:Male
  • Location:NY

Posted 12 February 2011 - 05:38 PM

:) It would be bigger than the armature Bill. Still, I seem to remember that a 5mm didn't fit...could be those misfiring brain cells though!

-john
John Havlicek





Electric Dreams Online Shop