Jump to content




Photo

Arm winding #1

Closed due to length

  • This topic is locked This topic is locked
3573 replies to this topic

#2176 Bill from NH

Bill from NH

    Age scrubs away speed!

  • Full Member
  • PipPipPipPipPipPipPipPip
  • 15,393 posts
  • Joined: 02-August 07
  • Gender:Male
  • Location:New Boston, NH

Posted 24 November 2010 - 11:09 PM

Before you resolder, measure the resistance from comm segment to comm segment to comm segment. If you get readings near zero, your solder connections are good. Robert, are you scraping off the wire's coating at the comm connections before soldering them? What did you use for flux?
Bill Fernald
 
I intend to live forever!  So far, so good.  :laugh2:  :laugh2: 




#2177 Robert V.

Robert V.

    On The Lead Lap

  • Full Member
  • PipPipPipPip
  • 350 posts
  • Joined: 14-November 09

Posted 24 November 2010 - 11:09 PM

Hi Kim

Thanks and i agree the power supply suggest short but all the meter reading say no, if i figure this out as you said it should be a screamer, i will keep all you guys posted.


Robert Vaglio

#2178 Robert V.

Robert V.

    On The Lead Lap

  • Full Member
  • PipPipPipPip
  • 350 posts
  • Joined: 14-November 09

Posted 24 November 2010 - 11:23 PM

Hi Bill

I just did the resistance test as you said on a good arm and this arm and i get near zero on both, i made shore i scraped off the laquer coating on all the connections to the comm tabs until i got bare copper, your going to love this i think i use the flux the plumbers use to sweat copper pipes and i have been using this stuff since my first rewind and i have not had a failure in about a dozen arms, i have heard that you should not be using acid flux at all but it shore works good.
Robert Vaglio

#2179 Champion 507

Champion 507

    Checkered Flag in Hand

  • Full Member
  • PipPipPipPipPipPip
  • 1,522 posts
  • Joined: 06-March 09
  • Gender:Male
  • Location:OK

Posted 25 November 2010 - 04:09 AM

Robert,

What kind of output amps does your power supply have? That #24 wire will suck the power. If the power supply doesn't have the amps the motor won't run. Kinda like trying to start your car with an almost dead battery. If the power supply has an overload light and it comes on, it may be that it isn't powerful enough to run the motor.

I have an old model train transformer that I use to break in Deathstars and the like and it works great for that. But if I were to try running a #24 wire motor on it, the overload light would come on and the motor wouldn't run. It's not powerful enough.

If your power supply is one of the ones by Koford or one of the other slot car manufacturers, then disregard my above information. You should have all the power you need.
Doug Azary
"We offer prompt service... no matter how long it takes!"
"We're not happy unless you're not happy"
"You want it when?"

#2180 Robert V.

Robert V.

    On The Lead Lap

  • Full Member
  • PipPipPipPip
  • 350 posts
  • Joined: 14-November 09

Posted 25 November 2010 - 08:11 AM

Hi Doug

Thanks Doug you may be onto something my bench top supply was an ebay find a few years ago and it only goes up to 3 amps, i will give my HO supply a try i think it goes up to 5 amps i will run a quick test and let you guys know what happens. :D
Robert Vaglio

#2181 Robert V.

Robert V.

    On The Lead Lap

  • Full Member
  • PipPipPipPip
  • 350 posts
  • Joined: 14-November 09

Posted 25 November 2010 - 08:28 AM

Hi Doug

Doug wins the prize my power supply does not have enough amps to run the motor i dug out my old Koford power supply which seams to have a bad digitlial display but appears to work other wise i spun the motor up to 7 volts and it's a screamer however i don't dare spin it up any higher because it's not tied and still needs a coat of epoxy. Thanks Doug and thanks to everyone else for all the help, now i need a better supply but don't have the money for that maybe Koford can repair the old one i will check into that.
Robert Vaglio

#2182 havlicek

havlicek

    OCD Rewinder

  • Subscriber
  • PipPipPipPipPipPipPipPip
  • 11,198 posts
  • Joined: 20-August 07
  • Gender:Male
  • Location:NY

Posted 25 November 2010 - 08:33 AM

...as they say in NYC...Oy! Robert, if the arm is indeed good, it's going to draw more than 3 amps. I agree with Doug, that "could" be your problem. A 17/24 should be able to "dim the lights in Fresno"...even if you do live on the other coast! :) Your arm should be reading down around .1ohm to .2 ohm when tested for resistance com plate to com plate if everything is OK. Many decent meters will give you some sort of reading at such low resistance values that may or may not be super accurate, so you're looking for the meter to "behave" similarly with each reading more than an actually useful reading in some cases. If the meter CAN resolve that low, even things like corrosion on the com segments can affect the reading...heck you could get a different reading at the com segments than you do at the tabs if your meter is capable of such fine resolution.

I don't know if I said it above, but the wind DOES look fine. If you want to chase the neatness thing, I'm sure you'll be able to get that. More than anything else I could say, it's just a matter of throwing-away a lot of wire. I can't really verbalize what to do, so much as to just say...go for it and it will happen!

-john
John Havlicek

#2183 Robert V.

Robert V.

    On The Lead Lap

  • Full Member
  • PipPipPipPip
  • 350 posts
  • Joined: 14-November 09

Posted 25 November 2010 - 09:17 AM

Hi John

I had know idea the motor would draw more than 3 amps it never entered my mind but my little test on the old Koford supply proves that the motor runs and seams to run really good i have checked the Koford again and it will not adjust past 7.5 volts on the meter but seams to run other wise, now at least i know the motor runs and i can finish the build. Does any body know of a cheap power supply that will run these kind of high powered motors my budget is very low and i can't afford to buy one of those compact units from any of the slot car places i think i would need 0-15 volts and at 0-5amp minimum maybe 6 amps. Thanks again John i think the neatness thing will come in time with several more winds i will just keep at it.
Robert Vaglio

#2184 havlicek

havlicek

    OCD Rewinder

  • Subscriber
  • PipPipPipPipPipPipPipPip
  • 11,198 posts
  • Joined: 20-August 07
  • Gender:Male
  • Location:NY

Posted 25 November 2010 - 10:13 AM

Hi Robert,

That's great news! Indeed, some of the big wire arms will draw enough current :shok:...to be getting into arc-welder territory (well not really, but I sometimes get lost in hyperbole!). As for power supplies, there are some "lab-type" supplies that will do whatever you might need...but they're still in the mid-$100 range and not very compact. I found one that's around $140 and it turns out some people here have used one and it seems to be good. The one I found is by Mastech and will do up to 20A @ up to 15V or 300watts. It shouldn't be breathing hard no matter what you put on it. I don't know how "clean" it's output is though, and that's important for these motors, although I suspect it's fine.

On the subject of #24awg arms, I just got back a 20T/#24 arm I did for a Mura B-motor resto from Bill Bugenis for dynamic balancing and he told me he got it balanced down to "zero". This thing ran like a mutha-on-steroids with some noticeable imbalance beforehand, so I figured it deserved Bill's services. I haven't had a chance to get it back into the old Mura setup yet, but this was one of those "scarey arms" and should be pretty crazy.:

Posted Image

This was one I wound using Bill's stack and com also, and those have proven themselves under the harsh conditions of eurosports so the arm has some more "insurance" built in by the components used. ***Of course, when you're doing #23/#24...even #25 arms anything can happen and every little detail colunts. That's not to mention the actual setup. These motors are "bad medicine" and problems. errors, inconsistencies are multiplied in their effect many times and can lead to failure. On the other hand, that's why I find everything from the old Muras to the modern eurosports motors to be so fascinating. :)

-john
John Havlicek

#2185 Robert V.

Robert V.

    On The Lead Lap

  • Full Member
  • PipPipPipPip
  • 350 posts
  • Joined: 14-November 09

Posted 25 November 2010 - 10:24 AM

Hi John

Thanks John i am looking into a few areas for a new supply i am no big hurry as for now my damaged Koford will have to do for the high powered stuff. That arm looks very powerful and as always your work is super neat and clean.
Robert Vaglio

#2186 havlicek

havlicek

    OCD Rewinder

  • Subscriber
  • PipPipPipPipPipPipPipPip
  • 11,198 posts
  • Joined: 20-August 07
  • Gender:Male
  • Location:NY

Posted 25 November 2010 - 10:28 AM

Hi Robert,

Just in case the Koford can't be repaired for a reasonable amount and in case anyone else is looking in, Here's a Link To The Mastech Supply I Mentioned.

-john
John Havlicek

#2187 Victor Poulin

Victor Poulin

    Posting Leader

  • Full Member
  • PipPipPipPipPipPipPip
  • 2,097 posts
  • Joined: 04-March 08
  • Gender:Male
  • Location:Raymond, NH

Posted 25 November 2010 - 11:53 AM

John,
That's a pretty cool unit for the money! The only thing I question is the amp output. How do you know how many amps to crank up? Is there a norm?
I have the WrightWay power supply, but I'm not even sure how many amps it puts out.

This unit you have looks pretty hard to beat for the price ;)

Vic
Alright, who cut the cheese?

#2188 havlicek

havlicek

    OCD Rewinder

  • Subscriber
  • PipPipPipPipPipPipPipPip
  • 11,198 posts
  • Joined: 20-August 07
  • Gender:Male
  • Location:NY

Posted 25 November 2010 - 12:28 PM

That's a pretty cool unit for the money! The only thing I question is the amp output. How do you know how many amps to crank up? Is there a norm?



Hi Vic...that's not the way these things (DC motors) work. As long as there's enough current available, the motor will be happy. In other words, you would just set the current/amperage for a value higher than the motor will draw; you could just leave the current set to max and never have to worry about it. That's not the case with voltage...the more voltage, the faster the motor will run until...POOF! Also, for breaking-in a motor you would set the voltage for much less than it would be run at normally, maybe 2-3V or whatever.

-john
John Havlicek

#2189 Victor Poulin

Victor Poulin

    Posting Leader

  • Full Member
  • PipPipPipPipPipPipPip
  • 2,097 posts
  • Joined: 04-March 08
  • Gender:Male
  • Location:Raymond, NH

Posted 25 November 2010 - 12:37 PM

Yep !! That makes perfect sense . Gee, for that price I wouldn't mind getting one to use in conjunction with my WrightWay. There are many times I wish I could be running in a couple motors at the same time.

Vic
Alright, who cut the cheese?

#2190 Robert V.

Robert V.

    On The Lead Lap

  • Full Member
  • PipPipPipPip
  • 350 posts
  • Joined: 14-November 09

Posted 25 November 2010 - 12:42 PM

Hi Vic

Well John beat me to the anwser on that one, i saw a wrightway power supply i believe it was the cheaper one and it had 4 amp max so i would guess that you have at least 6 amps.
Robert Vaglio

#2191 Victor Poulin

Victor Poulin

    Posting Leader

  • Full Member
  • PipPipPipPipPipPipPip
  • 2,097 posts
  • Joined: 04-March 08
  • Gender:Male
  • Location:Raymond, NH

Posted 25 November 2010 - 12:56 PM

Hi Vic

Well John beat me to the anwser on that one, i saw a wrightway power supply i believe it was the cheaper one and it had 4 amp max so i would guess that you have at least 6 amps.


Rob,
I'm not sure what mine has, as it doesn't appear to be marked on it. I'll have to go take another look at it after a nice turkey dinner :laugh2: That is, if I'm able to waddle out to the shop :rolleyes:
Alright, who cut the cheese?

#2192 Robert V.

Robert V.

    On The Lead Lap

  • Full Member
  • PipPipPipPip
  • 350 posts
  • Joined: 14-November 09

Posted 25 November 2010 - 10:54 PM

Hi guys

I finished the arm and the motor the comm looks a little dirty because after i cut it i reinstalled it in the motor just wanted to make shore it was working good it's a real screamer all the way up to the 7 volts the power supply goes up to. I may just use this motor as a test mule for future high performance builds not shore yet.

Posted Image
Posted Image
Robert Vaglio

#2193 Bill from NH

Bill from NH

    Age scrubs away speed!

  • Full Member
  • PipPipPipPipPipPipPipPip
  • 15,393 posts
  • Joined: 02-August 07
  • Gender:Male
  • Location:New Boston, NH

Posted 25 November 2010 - 11:08 PM

I don't have Les Wright's current specs, but would question if any of his supplies only has a 4 amp output. I have a Wright Way supply about 10 years old & it puts out way more. The Heathkit supply I built in the early '70s outputs 15 amps of filtered current & more than 20 amps of unfiltered current, both at the same time, if needed. The downside of it is it's a big as a car battery. :)
Bill Fernald
 
I intend to live forever!  So far, so good.  :laugh2:  :laugh2: 

#2194 Robert V.

Robert V.

    On The Lead Lap

  • Full Member
  • PipPipPipPip
  • 350 posts
  • Joined: 14-November 09

Posted 25 November 2010 - 11:24 PM

Hi Bill

You may be correct on the amps Bill i not at all shore of the specs but i think saw one of the guys at the track last week with a new one and it looked about the same size as all the others maybe it was the one they call a mini supply.
Robert Vaglio

#2195 havlicek

havlicek

    OCD Rewinder

  • Subscriber
  • PipPipPipPipPipPipPipPip
  • 11,198 posts
  • Joined: 20-August 07
  • Gender:Male
  • Location:NY

Posted 26 November 2010 - 06:20 AM

It looks great Robert and the big wire arms aren't easy either! It's a real thrill to do one of these and have it work...I don 't know what it is, but it's very habit-forming. :) Congrats!

-john
John Havlicek

#2196 Robert V.

Robert V.

    On The Lead Lap

  • Full Member
  • PipPipPipPip
  • 350 posts
  • Joined: 14-November 09

Posted 26 November 2010 - 08:20 AM

Hi John

Thanks John i am happy it worked and also unhappy it worked because now i need a new power supply to support these hot motors. :D
Robert Vaglio

#2197 Victor Poulin

Victor Poulin

    Posting Leader

  • Full Member
  • PipPipPipPipPipPipPip
  • 2,097 posts
  • Joined: 04-March 08
  • Gender:Male
  • Location:Raymond, NH

Posted 26 November 2010 - 08:50 AM

Rob,
The motor looks great!!! See,, it's amazing what can be done if you keep an open mind and put the time and effort into into something :D
Alright, who cut the cheese?

#2198 Champion 507

Champion 507

    Checkered Flag in Hand

  • Full Member
  • PipPipPipPipPipPip
  • 1,522 posts
  • Joined: 06-March 09
  • Gender:Male
  • Location:OK

Posted 26 November 2010 - 10:44 AM

Good job Robert! Keep it up.:good:

Vic, you're next. Can't wait to see what you come up with.:D
Doug Azary
"We offer prompt service... no matter how long it takes!"
"We're not happy unless you're not happy"
"You want it when?"

#2199 jockefors

jockefors

    On The Lead Lap

  • Full Member
  • PipPipPipPip
  • 308 posts
  • Joined: 13-November 10
  • Gender:Male
  • Location:Sweden

Posted 26 November 2010 - 11:31 AM

Hi when you wind a arm can you make it run harder and change the degrees of the arm when you build it ?
like hawing thiker cabels in the vinding,less or more turns on the arm.....
If cars were built to fly... they will have wings...

Joakim Forsman

#2200 Victor Poulin

Victor Poulin

    Posting Leader

  • Full Member
  • PipPipPipPipPipPipPip
  • 2,097 posts
  • Joined: 04-March 08
  • Gender:Male
  • Location:Raymond, NH

Posted 26 November 2010 - 11:48 AM

Good job Robert! Keep it up.:good:

Vic, you're next. Can't wait to see what you come up with.:D



Doug,
I cant come up with to many ideas that you guys haven't already done lol. I do have a couple more tricks that I,m going to try though ;) As far as trying my first wind, I'm going to get together with Bill soon and have him teach me the ends and outs, before I attempt trying it on my own. I'd just feel better with him showing me hands on.

And speaking of turns Doug,, I think it's time you get your hands dirty again :laugh2: Whatta ya think guys??
Alright, who cut the cheese?





Electric Dreams Online Shop