Jump to content




Photo

Arm winding #1

Closed due to length

  • This topic is locked This topic is locked
3573 replies to this topic

#2301 Bill from NH

Bill from NH

    Age scrubs away speed!

  • Full Member
  • PipPipPipPipPipPipPipPip
  • 15,393 posts
  • Joined: 02-August 07
  • Gender:Male
  • Location:New Boston, NH

Posted 11 December 2010 - 05:52 PM

Poster putty at a stationary store makes a good substitute for magnet putty. Years ago when I sanded magnets, I'd coat the dirty/dusty magnets with a tire dressing, such as Stick-it. I would first remove most of that mixture with a dry Q-tip, then wipe them down with a lighter fluid soaked rag to remove anything remaining. This process would also work when honing.
Bill Fernald
 
I intend to live forever!  So far, so good.  :laugh2:  :laugh2: 




#2302 Champion 507

Champion 507

    Checkered Flag in Hand

  • Full Member
  • PipPipPipPipPipPip
  • 1,522 posts
  • Joined: 06-March 09
  • Gender:Male
  • Location:OK

Posted 12 December 2010 - 02:49 AM

Don't laugh, Silly putty works great and it's cheap. Back when I used to work on slot car motors, I used it all the time. Then when I got bored, I could make reverse impressions of comics in the funny papersPosted Image
Doug Azary
"We offer prompt service... no matter how long it takes!"
"We're not happy unless you're not happy"
"You want it when?"

#2303 zipper

zipper

    Checkered Flag in Hand

  • Full Member
  • PipPipPipPipPipPip
  • 1,140 posts
  • Joined: 11-August 10
  • Gender:Male
  • Location:Finland

Posted 12 December 2010 - 04:59 AM

I've used Blu-Tack for years. The older and slimier from leftover dirt the better...
Pekka Sippola

#2304 havlicek

havlicek

    OCD Rewinder

  • Subscriber
  • PipPipPipPipPipPipPipPip
  • 11,198 posts
  • Joined: 20-August 07
  • Gender:Male
  • Location:NY

Posted 12 December 2010 - 07:38 AM

I've also used regular plumber's putty with some success. Roll it in your hands the way you would for plumbing to soften it and smoosh it in there. It's not the tackiest / stickiest thing, but it does get into the crevices better than rolled-up tape. With all the answers above...I should have included this in my post about old-school slot car tech :D Slot enthusiasts are a resourceful bunch!

-john
John Havlicek

#2305 havlicek

havlicek

    OCD Rewinder

  • Subscriber
  • PipPipPipPipPipPipPipPip
  • 11,198 posts
  • Joined: 20-August 07
  • Gender:Male
  • Location:NY

Posted 12 December 2010 - 09:51 AM

I got the setup all dun-dee-dun-dun for the latest Strapnut (the #24). It came out really nicely, and now I just have to resist the temptation to static balance the arm and spin it up. :rolleyes: This little motor is going to be intreresting :shok:

Posted Image

-john
John Havlicek

#2306 Victor Poulin

Victor Poulin

    Posting Leader

  • Full Member
  • PipPipPipPipPipPipPip
  • 2,097 posts
  • Joined: 04-March 08
  • Gender:Male
  • Location:Raymond, NH

Posted 12 December 2010 - 10:50 AM

Wow !! Now that's COOOOOL :) I see that you used my favorite, Mura hardware. What did you use for the endbell?
Alright, who cut the cheese?

#2307 havlicek

havlicek

    OCD Rewinder

  • Subscriber
  • PipPipPipPipPipPipPipPip
  • 11,198 posts
  • Joined: 20-August 07
  • Gender:Male
  • Location:NY

Posted 12 December 2010 - 10:57 AM

Hi Vic,

Thanks. The endbell and hardware are both Mura. I prefer to use the Mura endbell because it's symetrical top and bottom. The PS endbell is more compact, but it has a space at the bottom where it would normally meet the can edge (which doesn't exist in these strap conversions). It makes trimming and mounting the endbell more difficult and something of a crapshoot on these little guys. I also installed a set of the small heatsinks from the earlier Mura endbells to raise the brush hardware because the bottom brush plates were just barely clearing the com tabs. I have to look around, but this may be one of the last Mura endbells I have. Anyway, the setup came out nicely and the arm should be a real screamer...we shall see!

-john
John Havlicek

#2308 jockefors

jockefors

    On The Lead Lap

  • Full Member
  • PipPipPipPip
  • 308 posts
  • Joined: 13-November 10
  • Gender:Male
  • Location:Sweden

Posted 12 December 2010 - 11:02 AM

Nice work... strapcans are sexy ..or like a finne woman..perfektly build...LOL

hawe a litel thing for you...do you think its possible to puch in a "old Long g27 arm" ..from a strapcan engine in a shortend c-can engine..
i hawe tested and put it too geather and it seems too be possible i only hawe too chimm the arm a littel at the geer side and cut the can off
in the rear..
only ****..was that the can i plan too do this with was nott good for the jobb it is probably some year newer than the others a hawe and they hawe
taken a way some steel from the can witch a want to hawe left...grr

one problem is that i must soilder the can too gather when i cut it off the orginal soilder is in the back of mura cans

do you think i can weld the can too gather with TIG welding ? its just a littel point i need too weld...
If cars were built to fly... they will have wings...

Joakim Forsman

#2309 havlicek

havlicek

    OCD Rewinder

  • Subscriber
  • PipPipPipPipPipPipPipPip
  • 11,198 posts
  • Joined: 20-August 07
  • Gender:Male
  • Location:NY

Posted 12 December 2010 - 11:12 AM

Hi Joakim,

For me, the strap-type can seems cool because it should allow for a little better heat-dissipation and the lightest weight (these weigh around 22 grams on the button) and with the neos, the magnetic field seems plenty strong even with most of the can removed.

On your question, I prefer to use one-piece cans when possible for these kinds of motors but I suppose you could weld the can back together. I made a "long can" 26D a couple of years ago by soldering the rear end of a C-can to an old Mabuchi 26D can that i cut the bushing end off of and it seemed plenty strong after the fact. The bottom line is that you just start with an idea...try the pieces by eye to see if they might work and then just start cutting and shaping until things either fit or you throw the whole mess out!

-john
John Havlicek

#2310 Victor Poulin

Victor Poulin

    Posting Leader

  • Full Member
  • PipPipPipPipPipPipPip
  • 2,097 posts
  • Joined: 04-March 08
  • Gender:Male
  • Location:Raymond, NH

Posted 12 December 2010 - 12:24 PM

John,
I meant to ask you, Whats the best way to remove the magnets from these mini's ? I can't seem to budge these things from the cans.:angry:

Vic
Alright, who cut the cheese?

#2311 havlicek

havlicek

    OCD Rewinder

  • Subscriber
  • PipPipPipPipPipPipPipPip
  • 11,198 posts
  • Joined: 20-August 07
  • Gender:Male
  • Location:NY

Posted 12 December 2010 - 12:35 PM

John,
I meant to ask you, Whats the best way to remove the magnets from these mini's ? I can't seem to budge these things from the cans.:angry:

Vic


Hi Vic,

On the ceramics, I just heat the can a little and they pop right out (I remove the retainer springs first). They can easily be rezapped if needed, but I haven't had to heat them that much that they lost any charge. On the neos, I also remove the springs and then just brush on a little acetone (nail polish remover also works fine) so that it soaks into the joint between the can and the magnet. They will pop right out after a little soak-in time. Careful with either the acetone or the nail polish remover (which is acetone with some other junk in there)...both are really flammable so no open flames or sparks...put out that Marlboro for cryin' out loud! :)

-john
John Havlicek

#2312 Victor Poulin

Victor Poulin

    Posting Leader

  • Full Member
  • PipPipPipPipPipPipPip
  • 2,097 posts
  • Joined: 04-March 08
  • Gender:Male
  • Location:Raymond, NH

Posted 12 December 2010 - 01:11 PM

Hi Vic,

...put out that Marlboro for cryin' out loud! :)

-john


LMAO, You nailed me on that one John :laugh2: I've always got a butt hangin out of my mouth!! However''''''''' you forgot to mention the ice cold Miller light :shok:

Thanks for the tips John, I'll give that a try this afternoon. I think Santa may give me a toaster oven for Christmas. I'll need it for arms anyways ;)

Vic
Alright, who cut the cheese?

#2313 Alchemist

Alchemist

    Posting Leader

  • Full Member
  • PipPipPipPipPipPipPip
  • 2,840 posts
  • Joined: 11-November 09
  • Gender:Male
  • Location:Far, far away

Posted 12 December 2010 - 02:04 PM

John,

You've unearthed another diamond!! Beautiful motor John!

I really wish there was a way to upload soundbites of the motors running on voltage!! That would be way KOOL!

Ernie
Ernie Layacan

#2314 jockefors

jockefors

    On The Lead Lap

  • Full Member
  • PipPipPipPip
  • 308 posts
  • Joined: 13-November 10
  • Gender:Male
  • Location:Sweden

Posted 12 December 2010 - 02:39 PM

Hi Joakim,

For me, the strap-type can seems cool because it should allow for a little better heat-dissipation and the lightest weight (these weigh around 22 grams on the button) and with the neos, the magnetic field seems plenty strong even with most of the can removed.

On your question, I prefer to use one-piece cans when possible for these kinds of motors but I suppose you could weld the can back together. I made a "long can" 26D a couple of years ago by soldering the rear end of a C-can to an old Mabuchi 26D can that i cut the bushing end off of and it seemed plenty strong after the fact. The bottom line is that you just start with an idea...try the pieces by eye to see if they might work and then just start cutting and shaping until things either fit or you throw the whole mess out!

-john


Hi thank you ..
problem is when i shorten the can from the back side ...the can has a weld point at the back side,,,,and if i cut like 5 mm away it vill go away....so i hawe too make a new veld too keep the can from separating a part
i think i will hawe a topp and a bottom part if i dont fix new weld points... before i cut it off it will probably work if i soilder it with silver

its nott to cut in like new parts or some thing like that...problem is only that the orginal weld point is sitting a littel bit bad for shorten the can a bit

Attached Images

  • endbell 22.JPG

If cars were built to fly... they will have wings...

Joakim Forsman

#2315 Robert V.

Robert V.

    On The Lead Lap

  • Full Member
  • PipPipPipPip
  • 350 posts
  • Joined: 14-November 09

Posted 12 December 2010 - 04:16 PM

Hi John

Awsome motor looks a little like a group 27 those things really spin as i am shore this one does to.
Robert Vaglio

#2316 Bill from NH

Bill from NH

    Age scrubs away speed!

  • Full Member
  • PipPipPipPipPipPipPipPip
  • 15,393 posts
  • Joined: 02-August 07
  • Gender:Male
  • Location:New Boston, NH

Posted 12 December 2010 - 06:20 PM

Joakim, if you have access to a welder, go ahead & spot weld the cans on the seams where you show. You could also silver solder the seams instead for some added strength. :)
Bill Fernald
 
I intend to live forever!  So far, so good.  :laugh2:  :laugh2: 

#2317 havlicek

havlicek

    OCD Rewinder

  • Subscriber
  • PipPipPipPipPipPipPipPip
  • 11,198 posts
  • Joined: 20-August 07
  • Gender:Male
  • Location:NY

Posted 12 December 2010 - 06:33 PM

Hi Robert,

Thanks...I'm hoping it runs like one :)

Also, besides Bill's advice...I have silver soldered shim stock to the outside of cans so that when the weld is cut away, the can doesn't fall apart. If you tin the can and shim first with acid, then reflux and heat with the shim in place, it can come out looking pretty slick. I have done a whole bunch of cut down modern Mura C cans (what I call my "Walnuts") and you can cut them pretty far back to make quite a short motor without disturbing the weld. The cans are well-formed and I can't imagine it would be very useful to cut them much shorter anyway. here's one alongside a stock C-can for comparison:

Posted Image

Any shorter and you'd have to start hacking-up the magnets and/or the inside of the endbell to get it to go together. You can see on the top stock Mura C-can where the weld is and I'm still fairly far away from it when I cut the can.
John Havlicek

#2318 jockefors

jockefors

    On The Lead Lap

  • Full Member
  • PipPipPipPip
  • 308 posts
  • Joined: 13-November 10
  • Gender:Male
  • Location:Sweden

Posted 12 December 2010 - 06:41 PM

Joakim, if you have access to a welder, go ahead & spot weld the cans on the seams where you show. You could also silver solder the seams instead for some added strength.


Yepp
i will do so ... I like the ide of TIG welding ..strong and werry littel het in the can... but soldreing with silver is working too.....
and Bdw i am a welder from the begining hawe Tig welded a lot in my days ...

her is a new pic witch i hope clear things up...:blink:

Attached Images

  • endbell 2222.JPG

If cars were built to fly... they will have wings...

Joakim Forsman

#2319 Bill from NH

Bill from NH

    Age scrubs away speed!

  • Full Member
  • PipPipPipPipPipPipPipPip
  • 15,393 posts
  • Joined: 02-August 07
  • Gender:Male
  • Location:New Boston, NH

Posted 12 December 2010 - 06:49 PM

Any shorter and you'd have to start hacking-up the magnets and/or the inside of the endbell to get it to go together.


John, are you aware that Proslot sells a Mega III ceramic c-can magnet that's .450" long? It's part# PS-912.
Bill Fernald
 
I intend to live forever!  So far, so good.  :laugh2:  :laugh2: 

#2320 jockefors

jockefors

    On The Lead Lap

  • Full Member
  • PipPipPipPip
  • 308 posts
  • Joined: 13-November 10
  • Gender:Male
  • Location:Sweden

Posted 12 December 2010 - 07:10 PM

Hi ..
john... if you look at my pic you see that my cans are older...the weld point of the can is not in the same place as they are on your cans...
and yepp i dont plan too make it shorter than your can...

but as bill say ther is diffrent mags to by, i think one pair i hawe is shorter
than the other and i assume that newer engins like the x12 or wasp engins hawe smaller mags
if the arm is only 350 its no use too hawe 500 long mags... and if its cobalt or ferrit mags they can be cuted off ..but i will not do it
its easyer too by a shorter pair...
If cars were built to fly... they will have wings...

Joakim Forsman

#2321 havlicek

havlicek

    OCD Rewinder

  • Subscriber
  • PipPipPipPipPipPipPipPip
  • 11,198 posts
  • Joined: 20-August 07
  • Gender:Male
  • Location:NY

Posted 12 December 2010 - 07:53 PM

John, are you aware that Proslot sells a Mega III ceramic c-can magnet that's .450" long? It's part# PS-912.



Hi Bill,

I might have some of those here, but figured that Joakim might have the stock stuff lying around rather than buying something. I also can cut down ceramic magnets pretty easily with diamond wheels. They pretty much zip right through the material...still it's good to know they're out there just in case!

Hi ..
john... if you look at my pic you see that my cans are older...the weld point of the can is not in the same place as they are on your cans...
and yepp i dont plan too make it shorter than your can..


Hi Joakim,

I understand that ;) I'm trying to suggest that there are inexpensive cans that might work better for you such as the newer Mura and others, rather than having to go through all that work...and you would be starting off with a lighter can as well.

Anyway, I got around to putting my Mura B motor back together after getting it back from Bill Bugenis for dynamic balancing and my god is this one completely ridiculous motor! :shok: Smooth as silk and just screams like...well ...an angry bee! I have no way of telling how much current it draws, but it actually seems like it could be run pretty hard and live (!?). It really should have shunts and spring insulation, but this is my favorite kind of motor...completely unreasonable and stoopid-powerful! :D Still, if you're into the vintage stuff...everyone oughtta have an angry "B", dontcha think?


Posted Image

-john
John Havlicek

#2322 jockefors

jockefors

    On The Lead Lap

  • Full Member
  • PipPipPipPip
  • 308 posts
  • Joined: 13-November 10
  • Gender:Male
  • Location:Sweden

Posted 13 December 2010 - 01:07 AM

Hello
Yes .. i agree and understand your point....and yes thes babys rock and they are working good still they are at least 20 years old but i like the work of doing them..just for fun

at our track ther is at least 20 driners witch hawe thes old engins in ther cars and they are doing a super jobb
fun part is that when i started first time to drive when i was like 8-10 years old this was the engin we used....

and yes i would love too hawe a new mura engine and a cool body with a angry wasp on...but i hawe too find a painter that fix this for me ..mura has the stickers for the spoiler
and a vill fix me some of those to put on ...it wil be like my retro car ..

Attached Images

  • angrywasp.gif

If cars were built to fly... they will have wings...

Joakim Forsman

#2323 havlicek

havlicek

    OCD Rewinder

  • Subscriber
  • PipPipPipPipPipPipPipPip
  • 11,198 posts
  • Joined: 20-August 07
  • Gender:Male
  • Location:NY

Posted 20 December 2010 - 07:04 AM

Posted Image

-john
John Havlicek

#2324 Champion 507

Champion 507

    Checkered Flag in Hand

  • Full Member
  • PipPipPipPipPipPip
  • 1,522 posts
  • Joined: 06-March 09
  • Gender:Male
  • Location:OK

Posted 20 December 2010 - 04:09 PM

Ok, John, what's the 411 on those little babies?
Doug Azary
"We offer prompt service... no matter how long it takes!"
"We're not happy unless you're not happy"
"You want it when?"

#2325 jockefors

jockefors

    On The Lead Lap

  • Full Member
  • PipPipPipPip
  • 308 posts
  • Joined: 13-November 10
  • Gender:Male
  • Location:Sweden

Posted 20 December 2010 - 04:58 PM

Hi is this wasps ? they where super short
it looks like a werry thick wire on those arms...wooo
If cars were built to fly... they will have wings...

Joakim Forsman





Electric Dreams Online Shop