103 replies to this topic

[MSwiss]

CR024 Premium inline hard tail / rail drag chassis.
 
The parts being "dropped" (separated), along with being plated from, IMO,  the premier plater for slot racing parts, provides a kit, truly, ready and easy, to assemble.

 

Say goodbye to rust.
 
Accepts all popular bolt in motors.

 

$19.95 retail each kit (as shown in top pic)
 

Includes triangular top brace for rock-solid back end, and middle X brace.

 

Back end assembles with perfect bearing alignment, without jigging.( BB's not included )

 

Mockup of assembled car. ( C/R plated wire and BB's not included )

 

One can use the front wheel supports from the CR027 Economy Nose Piece and body mount tube supports from the CR028 Economy tube supports, as an economical way to finish off the chassis with all easy to solder, plated parts.

[MSwiss]

CR025 1.5" long, plated nose piece
 
The same nose piece from the CR024 kit.
 
Legal for IRRA® racing, but without guide stops, more of a drag item.
 
$6.00 retail, packed as a single.
 

[MSwiss]

CR026 Economy FK / Minimotor plated motor mount.
 
Accepts JK and other FK motors, along with Proslot 4000 / 4001 / 4002 , rotated 90 degrees.
 
Can be used, as is, for both dual motor inline and sidewinder applications.
 
Also can be trimmed for single motor applications.
 
Six .063" holes for ease of alignment, when using 2 pieces for sidewinder applications.
 
Can be used with CR027 and CR028 for a $12.00 retail, plated, no bar, sidewinder chassis.
 
Using the more compact Proslot motor, the rails will line up without spacing out the 1" wide CR027 nose.
 
Only $6.00 retail, for a zip-loc bag of 2 pieces.
 

[MSwiss]

CR027 Economy, 1" wide, plated drag nose piece.
 
Offset axle uprights can be mounted two ways for four different axle positions, in relation to the the guide post.
 
Only $8.00 retail, for a zip-loc bag of 2 sets.($4.00 per nose and 2 axle support)
 

Shown, tab forward, for longer guide leads.

 

Shown, tab back, for shorter guide leads.

[MSwiss]

CR028 Economy plated pin tube supports.
 
"Stacked" .050" holes for common thin wall stainless pin tubing like Koford M259, to change the stance/rake on the body, using the same pin hole(s).
 
Note; while the holes on the 2 pcs. are evenly spaced, I think most will cut these up into small pieces.
 
The thin wall is somewhat bowed, up and down, from lasering the thin, non-enclosed section, rail.

They can be straightened with a minimal effort.

 

Once straightened, the holes are 2.00", center to center.
 
Only $6.00 retail, for a zip-loc bag of 3 sets of 2.($2.00 per set of 2 pieces)
 

[MSwiss]

CR029 Fast Action Flux
 
Racers have loved this super-strength acid flux, I've had, since 2005, when I opened the raceway.
 
I'm finally comfortable with a container, to hold it, so I'm making it available to the distributors.
 
Designed for superior results with stainless steel.
 
Generous 20ML (2/3 oz.) bottle.
 
Only $3.95 each
 

[MSwiss]

CR030-4, CR030-5 & CR030-7 prebent 1/2" spoilers
 
This has always been a popular item for me.
 
Precision bent from the best material, backed with a super-strong double stick tape, are the reasons these are currently used by multiple current top Retro racers.
 
Now available in .004", .005", and .007", they are approx. 3.170" wide, to easily fit the widest Retro bodies.

CR030-4  .004" thick $10.50 zip-loc bag of 6

CR030-5  .005" thick $10.50 zip-loc bag of 6
CR030-7  .007" thick $10.50 zip-loc bag of 6

 

[MSwiss]

CR031 alignment jig for Proslot 2000(PS-2002 and PS-2003) and 4000 (PS-4001, PS-4002B-B, PS-4002-FK, PS-4007) series, sealed motors
 
This a follow item to the original C/R alignment jig, except it uses a standard Koford alignment bar(s).
 
$20.00 each (note; this a a reduced markup item)
 

Precise height dimension, so when on a flat surface, hoods align at zero degrees.

 

Shown with two Koford M148 alignment bars (not included), but only one is required.

 

Also works with sealed Proslot D cans. With the taller motor, the jig does not sit level, but can easily be shimmed up, with tape.

 

[MSwiss]

CR032AT & CR032SB  3/4" wide, 2 degree angle, Retro FK/PS Minimotor, inline motor bracket.
 
Retro's racing's first commercially available, and most successful, angled bracket.
 
IE-The C/R bracket took 10 of 12 podium spots, along with 3 of the 4 TQ's, at R4/11, this past March.
 
The motor shaft aligns with the axle shaft, for the best/smoothest gear mesh, possible.
 
$10.00 each (note; this a a reduced markup item)
 
As shown, only as a flat. Easy to form and adjust.
 
AT suffix notates for axle tube (7/32" ID) installation.
 
SB suffix notates for straight bearing (3/16" ID) installation.


CR032SB


CR032AT

[MSwiss]

CR033AT & CR033SB  1" wide, 2 degree angle, Retro FK/PS Minimotor, inline motor bracket.
 
Retro's racing's first commercially available, and most successful, angled bracket.
 
The motor shaft aligns with the axle shaft, for the best/smoothest gear mesh, possible.
 
$10.00 each (note; this a a reduced markup item)
 
As shown, only as a flat. Easy to form and adjust.
 
AT suffix notates for axle tube (7/32" ID) installation.
 
SB suffix notates for straight bearing (3/16" ID) installation.
 

CR033SB


CR033AT

[MSwiss]

CR034SB  1.360" wide, 2 degree angle, Retro FK/PS Minimotor, inline motor bracket.
 
Retro's racing's first commercially available, and most successful, angled bracket.
 
The motor shaft aligns with the axle shaft, for the best/smoothest gear mesh, possible.
 
This super wide bracket supports the bearings at the widest practical dimension.
 
$12.00 each (note; this a a reduced markup item)
 
As shown, only as a flat. Easy to form and adjust.
 
SB suffix notates for straight bearing (3/16" ID) installation.(SB only available)
 

[MSwiss]

CR035 3/32" magnesium ultra-lite, axle collars.
 
For racers who like to keep their inline gear mesh, while testing different rear tires.
 
Not to be confused with heavier 4-40 screw, aluminum, or way heavier, 4-40 screw, plated brass ones.
 
Approximately .195" wide x .245" diameter.
 
Uses standard gear wrench, with your own favorite, 4-40 set screws.

I've never heard of anyone stripping these, comes with 2 set screw holes, for lightness, and a "second chance".
 
$4.95 pair
 

[MSwiss]

CR036 1/8" magnesium ultra-lite, axle collars.
 
For 1/8" axle / Hardbody racers, who like to keep their inline gear mesh, while testing different rear tires.
 
Not to be confused with heavier 4-40 screw, aluminum, or way heavier, 4-40 screw, plated brass ones.
 
Approximately .195" wide x .295" diameter.
 
Uses standard gear wrench, with your own favorite, 4-40 set screws.
 
$4.95 pair
 

[MSwiss]

CR037B & CR037R (These are discontinued)
 
5/8" diameter, white backed, meatball, featuring C/R's exclusive old school font.

Slightly smaller size ideal for F1.
 
Self-stick, for the outside of the body.
 
CR037B (blue) $4.00 per sheet
CR037R (red) $4.00 per sheet

 

Note; slight shadowing in spots are not on the actual product.
 

[MSwiss]

CR038B & CR038R (These are discontinued)
 
3/4" diameter, white backed, meatball, featuring C/R's exclusive old school font.
 
Self-stick, for the outside of the body.
 
CR038B (blue) $5.00 per sheet
CR038R (red) $5.00 per sheet
 
Note; slight shadowing in spots are not on the actual product.
 

[MSwiss]

CR039-A1GY, CR039-14GY, CR039-58GY,CR039-A1R, CR039-14R, CR039-58R, 3 and 4 color numbers.

(These are discontinued-they may possibly be resurrected in the future)
 
C/R's exclusive old school font, in 3 and 4 colors.
 
Great for vintage Hardbody Stockers and Modified's.
 
Self-stick, for the outside of the body.

 

See below post #49 to get an idea of their size.
 
CR039-A1GY all 1's, grey
CR039-14GY 1-4, grey
CR039-58GY 5-8, grey
CR039-A1R all 1's grey & red
CR039-14R 1-4, grey & red
CR039-58R 5-8, grey & red
 
All $4.00 per sheet
 
Note; slight shadowing in spots are not on the actual product.

4 color, with a touch of red.

3 color.

[MSwiss]

CR040-14B, CR040-58B, CR040-14G, CR040-58G, CR040-14R, CR040-58R, CR040-14Y, CR040-58Y, 2 color numbers.
 
C/R's exclusive old school font, in 2 colors.
 
Great for vintage Hardbody Stockers and Modified's.
 
Self-stick, for the outside of the body.
 
CR040-14B 1-4, blue
CR040-58B 5-8, blue
CR040-14G 1-4, green
CR040-58G 5-8, green
CR040-14R 1-4, red
CR040-58R 5-8, red
CR040-14Y 1-4, yellow
CR040-58Y 5-8, yellow
 
All $5.50 per sheet
 

Blue, green.


Red, yellow.

Here they are, on some 1/25 Hardbody cars, so one can get an idea of the size.

[MSwiss]

CR041 Gold plated lead wire holder.
 
$5.00 retail (zip-loc bag of 10 pcs.)
 

[MSwiss]

CR042 3/32" ID, approx. .170" long, brass pre-cut axle spacers
 
$8.40 retail (4 zip-loc bags of 6 pcs. /.35 cents per spacer)
 
A longer version of my super-popular .100" long spacers.
 
Along with use as axle apacers, these pre-cut 3/32" ID tubes can also be used as an easy to solder to, filler for small gaps in a motor installation, general gusseting, and lead wire routing.
 

[MSwiss]

CR043 .032" brass, CNC machined, Retro nose piece.
 
A new version of my super-flat, Retro nose piece, but with built in pans for optional torsion style bulds.
 
$28.00 each (note; this a a reduced markup item)
 

[MSwiss]

CR044 Wood pit caddy. (see CR045, for example of use)
 
$16.00 each (note; this a a reduced markup item)
 

[MSwiss]

CR045 Acrylic pit caddy
 
$24.00 each - will be in blue acrylic (note; this a a reduced markup item)
 

[MSwiss]

CR046 Backtrack motor installation block

 

While the pic shows a C can, Geary developed this motor installation block, which features a chassis hold down, with the hard Neo mag, Phoenix motor in mind.

 

He has been using it for awhile, and says it works great.

 

$50.00 retail each

 

(note; this a a reduced markup item)

 

 

[MSwiss]

CR047 3/32" ID, approx. .235" long, brass pre-cut axle spacers
 
$8.40 retail (4 zip-loc bags of 6 pcs. /.35 cents per spacer)
 
Yet, another longer version of my super-popular .100" long spacers, as my CR042, .170" long spacer, has been a hit.
 
Along with use as axle apacers, these pre-cut 3/32" ID tubes can also be used as an easy to solder to, filler for small gaps in a motor installation, general gusseting, and lead wire routing.
 

[MSwiss]

CR048 1/8" x 1/4" dia., econo axle ball bearings
 
$3.95 retail (1 pair per pack)
 
Nice quality axle ball bearings
 
Like my popular CR016, properly cleaned and checked for correct fit on (Koford M418) axle.